CEM150

Fastcrete Super Concrete Mortar – For Application Thickness of 1 to 2 inches

CEM150 Super Concrete Mortar is a one component rapid concrete repair mortar which requires only the addition of water to produce a durable, very rapid strength-gaining material for permanent repair of concrete. CEM150 Super concrete mortar is a special blend of Portland cement, graded silica sands and a proprietary admixture developed by International Chem-Crete Corporation.

Downloads

Technical Data Sheet

USES

CEM150 Super Concrete Mortar is designed for the durable repair of poured in place concrete and pre-cast concrete substrates which require a very rapid strength gain and high strength characteristics.

  • Factory Floors
  • Warehouse Floors
  • Hangars Floors
  • Loading Bays
  • Cold Storage and Dairy Plants
  • Highway Repairs

CEM150 is suitable where high impact resistance, compressive strength, good abrasion resistance, durable, and early strength gaining repairs are requirements.

ADVANTAGES

  • One component requires only the addition of water.
  • Excellent workability.
  • Excellent Adhesion to most Substrates.
  • High Compressive Strength.
  • Freeze /Thaw Resistant.
  • Does not contain any additive, which may cause corrosion of steel reinforcement.
  • Non-shrink.

PACKAGING

 

Product Packaging
CEM150 * 50 Lb (22.68 Kg) Bag

* Grey color cement powder with selected silica aggregate

TECHNICAL

 

Property

Value *

Standard

Compressive Strength,

psi (MPa)

1 day 4277 (29.50) ASTM C109
7 days 9311 (64.20)
28 days 11281 (77.78)
Flexural Strength,

psi (MPa)

1day 957 (6.60) ASTM C348
7 days 1523 (10.50)
28 days 1886 (13.00)
Setting Time**, minute Initial 150 ASTM C-191
Final 200
Pot Life**, minute 40

Density – set mortar,

Lb/Gal (Kg/Liter)

19.36 (2.32)

* Average

** Test at 75°F (25°C)

APPLICATION

Limitations: CEM150 Super Concrete Mortar is a water sensitive material, maintain recommended water volume criteria. Do not apply less than 1 inch (2.54 cm) in depth.

Do not add additional water to CEM150 once mixed to extend workability.

 

Water requirement: 0.78 Gallon (2.95 Liter) of water is required for the 50 Lb (22.68 Kg) Bag of CEM150. Accurate measurement of water is very essential.

 

Coverage:

Thickness Coverage of 50 Lb (22.7 kg) Bag
1” (2.54 cm) 6 ft² 0.37 m²
1 ½” (3.80 cm) 5 ft² 0.25 m²
1 ¾“ (4.44 cm) 4 ft² 0.21 m²
2” (5.08 cm) 3 ft² 0.18  m²

 

Note: The above coverage is for estimation purposes only. Slight variations in quantities may occur depending on thickness, site conditions, substrate conditions, etc.

 

Surface Preparation: When using a spalled or deteriorated area of concrete chip or saw cut the spalled area to a depth sufficient to remove all deleterious concrete. It is recommended that edges be squared and depth be a minimum of 1 inch (2.54 cm). Feather edging is not recommended. Clean and remove all oil, grease, dirt and loose debris from the area to be repaired.

 

Optional Vapor Barrier: Prime all areas with CHEM-CRETE SOFIX CCC100 or CHEM-CRETE CCC700 depending on site vapor conditions to serve as a percolation vapor barrier to the existing pre-treated concrete.

 

Optional Priming: Apply one coat of CHEM-BOND CCC550 to the area to be patched immediately prior to placing the CEM150 Mortar if required. Contact International Chem-Crete for details.

 

Mixing:

  • Use a high intensity mixer with at least twice the volume of the amount to be mixed. Locate the mixer close to the area to be repaired. Ensure that the mixer is clean of any foreign material including water.
  • Measure the total mixing water required for each batch. Use clean water for mixing. Accurate measure of water is very important.
  • Fill the mixer with half of the quantity of CEM150 to be mixed, and then add all the water. Mix for 90 seconds, then add the second half of CEM150 material and mix for 3-6 additional minutes until a uniform homogenous and smooth mixture is achieved.
  • Do not add any other materials to the mix.

 

Application: Place the mixed mortar in the area to be patched. Place from one side to the other and work the material into side and bottom of the repaired area to aid in satisfactory bonding.

 

Screed and level to maintain elevation of existing concrete. Finish by trowel to seal edges, surface, and ¾ inch (1.90cm) minimum keyed saw-cuts. Featheredging is not recommended.

 

Do not re-temper the mix by adding water.

 

Curing: Protect exposed areas from excessive heat or cold until setting is complete.

 

Cleaning: clean all mixing and application equipment with water immediately following use. Remove all splatter of spills with water before material sets.

STORAGE

Store CEM150 in   cool   dry   storage facilities. Do not expose to direct sunlight. The shelf life of CEM150 is minimum 1 year if stored in a cool dry place in its original unopened container.

SAFETY

CEM150 is a non-flammable and non-toxic in nature. Avoid contact with eyes and skin as it may cause irritation due to its alkaline nature. Splashes of CEM150 should be washed off immediately with clean water. Wear necessary gloves and dust mask.

WARRANTY

LIMITED WARRANTY:   International Chem-Crete Inc. warrants that, at the time and place we make shipment, our materials will be of good quality and will conform to our published specifications in force on the date of acceptance of the order.

 

DISCLAIMER:   The information contained herein is included for illustrative purposes only and, to the best of our knowledge, is accurate and reliable. International Chem-Crete Inc. is not under any circumstances liable to connection with the use of information. As International Chem-Crete Inc. has no control over the use to which others may put its products, it is recommended that the products be tested to determine the suitability for specific applications and/or our information is valid in particular circumstances. Responsibility remains with the architect or engineer, contractor and owner of the design, application and proper installation of each product. Specifier and user shall determine the suitability of the product for specific application and assume all responsibility in connection therewith.  AM200319.