CHEM-PRISON 20

Semi-Rigid Epoxy Gel with 20% Elongation

CHEM-PRISON 20 is an epoxy gel used for patching, bonding, surface sealing, and security caulking. It is semi-rigid with an elongation of 20%. It can be applied in non­sagging layers up to one inch thick. It can be supplied in three speeds of cure: standard, medium and fast. Specify speed of cure desired by referring to Pot Life Time.

Downloads

Technical Data Sheet

USES

  • Vertical and overhead applications
  • Can be used as a mortar binder up to one inch thick.

ADVANTAGES

  • 100% solids
  • Easy 1: 1 mix ratio
  • Vertical & horizontal application
  • No shrinkage
  • Fast Curing

PACKAGING

 

Product

Packaging

CHEM-PRISON 20 2 Gallon (7.57 Liters) Unit

Part A: 1 Gal Can, Part B: 1 Gal Can

10 Gallon (37.58 Liters) Unit

Part A: 5 Gal Pail, Part B: 5 Gal Pail

 

TECHNICAL

Technical Data for Unmixed Parts

Property @ 25°C (77°F)

Resin – Part A

Hardener – Part B

Test Method
Solids 100 % 100 %

Color Grey Clear

Density, Lb/Gal (Kg/L) 9.70 (1.16) < 8.2 (0.98) ASTM D-1475
Mixing Ratio A: B

1: 1 By Volume

Shelf Life 2 years 2 years

 

 

Technical Data for Mixed Parts

Property (Mixed A & B) Value @ 25°C (77°C) Test Method
Mixed Density, Lb/Gal (Kg/L) 11.2 (1.34) ASTM D-1475
Mixed Color Light Grey

Gel Time @ 60 grams, minute 40, 11, 7 ASTM D-2471
Pot Life @ 1 Gal (3.785 Liter), minute 20

Shore Hardness @ 3 Days, D 76 ASTM D-2240
Tensile Strength @ 7 Days, Psi (MPa) 6000 (40.8) D-638
Flexural Strength @ 7 Days, Psi (MPa) 4500 (30.6) D-790
Compressive Strength @ 7 Days, Psi (MPa) 6000 (40.8) ASTM D-695
Bond Strength to @ 7, Psi (MPa) 2350 (16) Concrete Failure ASTM C-882
Elongation, % 20 D-570
Final Cure, day 7

 

APPLICATION

Blend equal parts of A and B, then apply to a clean, dry, surface. It can be used as a mortar binder by adding 1-part sand when spall repair is needed on vertical or overhead areas.

 

Cleaning: remove uncured CHEM-PRISON 20 from tools and equipment with suitable solvents such as Xylene, Toluene or CHEM-CRETE BLENDED SOLVENT immediately after use. Cured material may only be removed mechanically.

STORAGE

The product can be stored for minimum of twelve months at temperature from 41°F to 95°F (5°C to 35°C) in the unopened original packaging.  Protect from direct sunlight.

SAFETY

After hardening thoroughly, CHEM-PRISON 20 is physiologically harmless. Keep the resin and hardener away from the eyes mouth and skin.  Do not breathe in the vapors.  The uncured mixture can cause irritation of the skin.  For best protection, wear rubber or plastic gloves.  In case of contamination, wipe away resin or hardener immediately from the skin using paper towels and then wash with soap and water or hand cleaning detergent. Empty resin and hardener cans must be destroyed. Under no circumstances use them to store food or drink even if they have been thoroughly cleaned.

WARRANTY

LIMITED WARRANTY:   International Chem-Crete Inc. warrants that, at the time and place we make shipment, our materials will be of good quality and will conform to our published specifications in force on the date of acceptance of the order.

 

DISCLAIMER:   The information contained herein is included for illustrative purposes only and, to the best of our knowledge, is accurate and reliable. International Chem-Crete Inc. is not under any circumstances liable to connection with the use of information. As International Chem-Crete Inc. has no control over the use to which others may put its products, it is recommended that the products be tested to determine the suitability for specific applications and/or our information is valid in particular circumstances. Responsibility remains with the architect or engineer, contractor and owner of the design, application and proper installation of each product. Specifier and user shall determine the suitability of the product for specific application and assume all responsibility in connection therewith.  AM29419.